Indirect standardization


00:00 / 00:00



Indirect standardization


Evaluation of diagnostic tests

Sensitivity and specificity

Positive and negative predictive value

Test precision and accuracy

Epidemiological measurements

Incidence and prevalence

Relative and absolute risk

Odds ratio

Attributable risk (AR)

Mortality rates and case-fatality


Direct standardization

Indirect standardization

Study design

Study designs

Ecologic study

Cross sectional study

Case-control study

Cohort study

Randomized control trial

Clinical trials

Sample size

Placebo effect and masking

Causation, validity and bias

Disease causality

Selection bias

Information bias



Bias in interpreting results of clinical studies

Bias in performing clinical studies

Public health

Modes of infectious disease transmission

Outbreak investigations

Disease surveillance

Vaccination and herd immunity



Indirect standardization


0 / 5 complete

USMLE® Step 1 questions

0 / 1 complete

USMLE® Step 2 questions

0 / 1 complete

High Yield Notes

7 pages


Indirect standardization

of complete


USMLE® Step 1 style questions USMLE

of complete

USMLE® Step 2 style questions USMLE

of complete

A researcher is studying the annual mortality rates of two Midwestern towns, Town A and Town B. The age distribution of the two towns are shown below:   

Table 1: Age distribution of Town A and B
 Age Range  Number of individuals in Town A within each age range  Number of individuals in Town B within each age range 
 0-20  2,000  5,000 
 21-40  3,000  8,000 
 41-60  3,000  8,000 
 80+  2,000  4,000 

The recorded number of deaths in Town B is 2,000/year. The mortality rates by age bracket are available for only Town A and shown below:   

Table 2: Mortality rates of Town A by age group  
 Age range  Town A annual mortality rate 
 0-20  1% 
 21-40  5% 
 41-60  8% 
 80+  15% 

Indirect standardization is performed using the mortality rates of Town A as the reference. Which of the following conclusions can be drawn from the above data?  


Content Reviewers

Rishi Desai, MD, MPH


Sam Gillespie, BSc

Evan Debevec-McKenney

Pauline Rowsome, BSc (Hons)

In epidemiology, we often want to compare the mortality rates, or the frequency of deaths, and the morbidity rates, or the frequency of a certain disease, in different populations.

Typically, we do this by calculating the crude mortality rate for each population, which is the number of deaths in that occur within a certain timespan, like a year, divided by the total number of people in the population.

For example, let’s say we want to compare the crude mortality rates in two cities - City 1, which has a population of 23,000 people, and City 2, which has a population of 26,000 people.

In one year, there were 68 deaths in City 1, and 105 deaths in City 2. So the crude mortality rate in City 1 is 68 deaths divided by 23,000 people, or 0.003. This means that there were 3 deaths for every 1,000 people that year in City 1.

The crude mortality rate for City 2 is 105 divided by 26,000, which equals 0.004, or 4 deaths per 1,000 people.

We can use a mortality ratio, or a ratio of two mortality rates, to compare the crude mortality rate of City 1 to the mortality rate of City 2, and we get a ratio of 3 to 4. And if we divide both sides by the bigger number, 4, we get a mortality ratio of 0.75 to 1, which means that, in one year, City 1 had a mortality rate 25% lower than City 2. That may convince some folks to pack their bags and move to City 1!

Sometimes though, calculating the crude mortality ratio doesn’t provide an accurate picture of the two populations, and this is usually because the populations have different distributions of certain characteristics, like age, sex, or race.

For example, let’s say City 1 and City 2 have different age distributions, so City 1 has an older population with a large percentage of people over the age of 40, whereas City 2 has a younger population with only a small percentage of people over the age of 40.

Typically, mortality rates tend to be higher in older populations and lower in younger populations. So, we can speculate that if City 2 has a smaller percentage of older people, then the crude mortality rate for City 2 might be lower. Perhaps it’s time to put down those bags and pick up a calculator instead.

Standardization is a method that’s used to adjust for differences in characteristics between two populations, and when standardization is used to adjust for age, the result is called an age-adjusted rate.


In statistics, standardization is a method used to adjust for differences in characteristics (e.g. mortality rates, incidence or prevalence rates, etc.) between two populations. When the number of events or the mortality rates in each age group is unknown, it is indirect standardization. On the other hand, when the number of events or the mortality rates in each age group is known, it is direct standardization.


Copyright © 2023 Elsevier, except certain content provided by third parties

Cookies are used by this site.

USMLE® is a joint program of the Federation of State Medical Boards (FSMB) and the National Board of Medical Examiners (NBME). COMLEX-USA® is a registered trademark of The National Board of Osteopathic Medical Examiners, Inc. NCLEX-RN® is a registered trademark of the National Council of State Boards of Nursing, Inc. Test names and other trademarks are the property of the respective trademark holders. None of the trademark holders are endorsed by nor affiliated with Osmosis or this website.