X-ray emission: Rad Tech
Producing a diagnostic radiograph requires control of the X-ray beam, specifically its intensity and energy. Intensity reflects photon quantity, whereas energy determines penetrability or the beam's ability to pass through tissue.
These characteristics affect image receptor exposure, image quality, and patient dose. As a radiologic technologist, understanding the factors that affect the X-ray beam guides the selection of exposure techniques, supports diagnostic image quality, and limits unnecessary radiation exposure.
Now, X-ray intensity is the quantity or number of X-ray photons in the useful beam. More photons increase image receptor exposure, while too few can increase image noise.
Because photon quantity also affects patient dose, intensity must be controlled. The main factors that affect X-ray intensity are milliampere seconds or MAS, kilovolt peak or KVP, distance, and filtration.
A milliampere is the rate of electron flow from cathode to anode in the X-ray imaging system. So milliampere seconds equals the number of electrons produced in a certain amount of time.
MAS controls X-ray beam quantity, so beam intensity rises in direct proportion to MAS. When more electrons strike the target, more photons are produced, increasing intensity and overall image receptor exposure.
Conversely, decreasing MAS lowers intensity and image receptor exposure. Because MAS changes photon quantity rather than energy, it does not change the penetrability of the X-ray beam, though it directly impacts patient radiation dose.
While MAS affects only quantity, KVP affects both X-ray beam quantity and energy. Remember that KVP is the maximum voltage applied across the X-ray tube during exposure, so increasing KVP gives electrons more kinetic energy as they cross the tube.
This produces more photons with higher average and maximum energies. As a result, the beam becomes more intense and more penetrating, allowing more photons to reach the image receptor.
Now, distance changes intensity without changing photon energy. As the distance from the X-ray source increases, the beam spreads over a larger area, reducing the number of photons that strike each unit of area, and intensity falls rapidly.
This relationship is described by the inverse square law and helps radiologic technologists adjust MAS to maintain image receptor exposure when the source to image receptor distance changes.
The final factor affecting the intensity of the X-ray beam is filtration, which lowers the intensity of the beam by preferentially removing low energy photons.
Because filtration is built directly into the X-ray tube and housing, it is not an adjustment controlled by the radiologic technologist.
These low energy photons would otherwise be absorbed by the patient rather than reach the image receptor, adding radiation dose without providing useful image information.
Removing them reduces the total number of photons while raising the average energy of the remaining beam. This change is known as beam hardening.
The resulting beam is less intense but more penetrating, and unnecessary patient exposure is reduced. X-ray beam energy describes the photon's average energy, and energy determines penetrability.
Higher energy photons are more likely to pass through thicker or denser anatomy and reach the image receptor, while lower energy photons are readily absorbed by tissue.
This penetrating ability or beam quality is influenced mainly by KVP and filtration. The half-value layer or HVL is the true measure of X-ray beam quality.
It represents the thickness of an absorber, usually aluminum, needed to reduce beam intensity by 50%. Because measuring HVL requires precise testing, it's evaluated by a medical physicist during routine quality control testing rather than by the radiologic technologist.
A higher HVL indicates greater beam penetrability and higher average photon energy. Now, there are 3 main factors that affect X-ray energy KVP filtration, and generator characteristics.
Increasing KVP raises the maximum and average photon energies. Increasing filtration removes more low energy photons, raising average but not maximum energy.
The type of generator determines the efficiency of power delivery to the tube. Generator characteristics determine voltage ripple, or how much tube voltage drops between peaks.
Low ripple three-phase and high frequency systems maintain voltage closer to the selected KVP producing a more intense beam with higher average energy than a single-phase system at the same KVP and MAS.
Together, these factors determine beam quality and penetrability. Alright, as a quick recap, X-ray intensity describes photon quantity while X-ray energy describes penetrability.
Increasing MAS raises intensity only, while increasing KVP raises both intensity and energy. Increasing distance lowers intensity and decreasing distance increases intensity.
Filtration also lowers intensity but raises average energy by removing low energy photons. A higher HVL indicates a more penetrating beam, and generator voltage ripple affects both intensity and average energy.
As a radiologic technologist, balancing these factors provides enough photons to control image noise and enough energy to penetrate anatomy and produce high quality diagnostic images while avoiding unnecessary patient dose.
- "Radiologic science for technologists: Physics, biology, and protection (13th ed.)" Elsevier (2026)
- "Principles of radiographic imaging: An art and a science (7th ed.)" Elsevier (2026)
No notes for this video yet
Try adding a note below